SKU: 63468605876

MRT ENGINEERING Spurstangen Roll-Center Bump-Steer Kit passend für BMW E30 E36 E46 Z3 Z4 einstellbar (Aluminium)

$423.00 $470.00
Save 10%
No.2 Bestseller on martinetexier.com >

Pay in installments of $117.50 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 31 - Aug 5

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

MRT ENGINEERING Spurstangen Roll-Center Bump-Steer Kit passend für BMW E30 E36 E46 Z3 Z4 einstellbar (Aluminium)Verstelbare bumpsteer Aanzienlijk lichter dan de originele trekstangen Spoorstangeinden met Uniball lagers Trekstangen van AW 7075 aluminium ALLEEN VERLAGEN IS NIET GENOEG Bij het verlagen van uw voertuig verandert de asgeometrie, die in de fabriekstoestand echter is uitgelijnd met de voertuighoogte. Uiteraard hebben deze veranderingen geen positief effect op het rijgedrag. Met deze trekstangen krijgt u weer een nauwkeurig stuurgevoel dankzij een

✅ Verstelbare bumpsteer
✅ Aanzienlijk lichter dan de originele trekstangen
✅ Spoorstangeinden met Uniball-lagers
✅ Trekstangen van AW-7075 aluminium

ALLEEN VERLAGEN IS NIET GENOEG

Bij het verlagen van uw voertuig verandert de asgeometrie, die in de fabriekstoestand echter is uitgelijnd met de voertuighoogte. Uiteraard hebben deze veranderingen geen positief effect op het rijgedrag. Met deze trekstangen krijgt u weer een nauwkeurig stuurgevoel dankzij een groot instelbereik van de bumpsteer.

VOLLEDIGE CONTROLE

Met de verstelbare trekstangenset voor BMW E30 / E36 / E46-modellen inclusief Z3 / Z4 en Compact (behalve E30 iX / E46 xi/xd-modellen en Z4M) krijgt u nieuwe, lichtere en zeer verstelbare trekstangen volgens 90-92 ' DTM-specificatie met extra instelbereik voor bumpsteer voor alle toepassingen. Dit ligt in het bereik van 10 mm tot 35 mm en kan in stappen van 5 mm worden gecorrigeerd.

VEEL LICHTER

De trekstangen zijn gemaakt van AW-7075 aluminium en de spoorstangeinden zijn gemaakt van CrMo-staal. Dit levert een enorme gewichtsbesparing op ten opzichte van de OEM trekstangen, zonder verlies aan stijfheid.

DETAILS

Kan op de E30 / E36 rekken geschroefd worden! Voor E46-rekken raden we aan om een ​​6 mm brede en 3 mm diepe geleidingssleuf voor de vorkkop te slijpen. De minimum aanbevolen wielmaat is 15" met E30 assen/gewrichten, 16" met E36 of E46 assen/gewrichten. Niet geschikt voor Z4M fusees.
Wordt geleverd met alle benodigde bevestigingsmateriaal.

De kit kan worden gebruikt met standaard staanders en ook als aanvulling op alle MRT Engineering RACE- of rolcentrumcorrectiekits.

Er is geen speciaal gereedschap nodig voor de montage, alle onderdelen worden rechtstreeks met bouten op de hardware vermeld in de artikelbeschrijving.

Heb je nog vragen? Neem dan gewoon contact met ons op!

Levering: 2x trekstangen (incl. montagemateriaal)

TECHNISCHE DATEN
fabrikant MRT-techniek
Geschikt voor E30 | E36 | E46 | Z4 (geen Z4M)
Materiaal AW-7075 aluminium, CrMo-staal
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 63468605876

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.0 ★★★★★
Based on 25 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
J
Verified Purchase
JBDoge
Cuba, US
★★★★★ 5
Wish they came with instructions...
They are cheap and work great. They plug right into my Pioneer vsx521 receiver and my Paradigm Atom monitor speakers. I wish they came with instructions, because it took me about 10 minutes to realize the bottom part unscrews in addition to the top part. Here are my instructions for installation: 1) Unscrew the bottom part of this connector (the thin metal underneath the red/black ring). 2) Make sure the Banana Plug (which may be loosely screwed into the top part of the connector) is fully tightened down 3) Strip your wire tips to 3/8 of an inch (or just slightly under) 4) Run the first newly stripped wire end through the bottom part you removed in step 1, such that the stripped end of the wire is entering through the flat end and exiting through the smaller threaded end. 5) Leave about 1/8 to 3/16 of an inch of stripped wire hanging past the exit hole. 6) As evenly spaced as possible, bend the over-hanging wire strands over the exit hole (all around it, like a hat). If done properly, the wire should not fall out if you give it a VERY GENTLE tug. 7) Screw the top metal part (with the actual banana plug) back onto the bottom part. It may be difficult if your stripped wire is hanging too low. I've used a pair of pliers to grip the bottom part of the connector while I twist the banana plug side with my hand. If done correctly, you should be able to put a lot of tension between the wire and connector without removing/damaging it. UPDATE: I just recently helped my dad install his 5.1 system without these... it sucked... This item (5 pairs of them in this case) and a good wire stripper can save you alot of pain (both physical and mental). The connectors on the back of his receiver are the kind where bare wire comes in from the side and then the connectors screw down (with a banana plug hole in the center which is where this product would come into play). I felt like a surgeon trying to get a bare wire end into the little slot, and then holding it there while I tighten the connector which is almost impossible since they are so close together... GET THESE!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 8, 2012
R
Verified Purchase
R. Jackson
Pawtucket, US
★★★★★ 1
'Monoprice' = Worst stereo banana plugs on T-H-E market.
Size: 5 Pack, Pattern Name: Banana Plugs
The absolute WORST in stereo banana plugs - HANDS DOWN. After installing stereos and components for over 30 years, I'd say I'm experienced. These banana plugs fail at EVERY part of the design. Allow me to explain... 1) Starting with the tips, they are loose off the bat and fit LOOSELY in either the stereo input studs or speaker input studs by their 'girth'. They do not firmly seat in any plug and for this setup, I'm using a nearly $2K setup all together. They 'rock' back and forth (when inserted) and thus create a non-permanent connection, again, seriously making these utter junk. I've seen some items you can get by with over the years, but these aren't even rock bottom. They are unusable! 2) Next, the banana plugs themselves comes as three pieces. No non loosening o-ring seal but a plastic colored want-to-be imitation for positive and negative notation. Why do these stupid things come in three pieces? - I simply can't tell you why. I do know they serve no specific piece to solving the puzzle of installation so why do they come in three pieces...? My speculation is they are cheap china knockoffs. 3) The 'way' in which you normally install the trimmed wiring internally with the 'two-piece' design permits you to firmly CRIMP and hold the unsheathed wiring; but these do not. The overlap/overlay of the exposed wiring can only be about 2/16's of an inch thus not much to create a proper connection with. This single fact eliminates these plugs as even worthwhile component add ons; period. If you can't achieve a good ground/wiring connection, these are a defeated purpose... 4) Because of the design of these, they have no room to crimp and screw on the cable so your forced to nearly break your fingers in an attempt to get the unsheathed wire to overlay the internal threading and twist them on with all your might. This in effect breaks nearly every wire thread internally and then they breaks off inside. Absolute garbage. These are total pieces of non-quality junk that did nothing but makes me waste 30 minutes on attempting to get them securely on and another 25 to locate my Amazon account, find this product in my order and ALARM anyone else from making the same mistake I made. Now, I find out I can't even get a return on these. Thanks Amazon. Thank you third party retailer. You just made me a very dissatisfied decade long customer.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on August 17, 2016
A
Verified Purchase
Amazon Customer
Dallas, US
★★★★★ 5
Nice quality
Had to return due to our mistake but the mechanic said it was good quality. Ordered the correct size and worked great.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 30, 2025
K
Verified Purchase
katelyn traut
Los Angeles, US
★★★★★ 5
Perfect fit
Worked great for a 1965 mercury thunderbolt 150hp
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 3, 2025
L
Verified Purchase
Lawrence Brown
Lake Worth, US
★★★★★ 5
MerCruiser Replacement Parts
OEM quality MerCruiser Alpha 1 Gen1 replacement part. Everything you need and some things you don't because it's a universal kit that works for several models.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on July 19, 2025

recommand products

Pasteri Hängeleuchte anthrazit Ø 53 cm
99.00
langer faltenrock mit grafischem druck max 5325_kaki
30.99
fliessende kombination mit stilisierter schlaufe max 5290_kaki
34.99
Pasteri Wandleuchte weiss/kupfer
79.00
elastisches kleid mit ruschenarmeln max 5277_creme
27.99