Pay in installments of $66.02 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 24 - Jul 29
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
PRO-TECH MULTI BEAD FORMING 7/8' 1/2'SH KPS5901Multi Bead Carbide Tipped This router bit is used for creating a single bead (also referred to as a reed) with fillets and a rounded edge with the same radius to give a classic rounded off finish in one pass. Control cut design helps minimize kickback Smooth edge requires little or no sanding before applying a finish This router bit has a 12,7mm shank (shaft) that will fit most large routers. Please ensure that you select a router bit with a shank
Multi-Bead
Carbide Tipped
This router bit is used for creating a single bead (also referred to as a reed) with fillets and a rounded edge with the same radius to give a classic rounded off finish in one pass.
- Control cut design helps minimize kickback
- Smooth edge requires little or no sanding before applying a finish
This router bit has a 12,7mm shank (shaft) that will fit most large routers. Please ensure that you select a router bit with a shank (shaft) size that will fit into your router collet.
PRO-TECH router bits are manufactured in Taiwan.
| consider safety for your health and the people around you | |||
General safety suggestions:It is advisable to always have the following items nearby and in a good condition
|
|||
|
Wear Gloves
|
Eye Protection
|
Hearing Protection
|
Dust Mask
|
Router Table Safety
Although most router bits are small, they can be potentially dangerous and should deserve your attention and respect.
1 Use push sticks or a push block to position your hands a safe distance from the router bit.
2 Use large-diameter bits only in a router table. Using bits over 25mm Ø (diameter) in a handheld router can possibly cause you to lose control of the tool and harm yourself or bystanders.
3 Always wear a dust mask as well as eye and hearing protection.
4 Take light cuts. Heavy cuts invite kickback. If necessary, move the fence closer to the bit or switch to a larger guide bearing/bush.
5 Use a featherboard (anti-kickback device) to support the workpiece against the router table and/or fence.
6 Never climb-cut. Always feed the stock from right to left. Against the rotation of the router bit. (see illustration)
7 Avoid routing small stock. Instead, rout a larger piece and cut it to size afterwards. If you absolutely have to profile a small piece, build an suitable jig or secure the workpiece.
8 Always use a guard. If the fence didn t come with a guard, make your own.
9 Never start the router with the bit in contact with the material.
10 Don t force the router bit or overload the router. Excessive heat is an enemy.
11 Secure/fasten the router in the base before starting/switch on the router.
12 Don t bottom out the bit in the collet or partially insert the bit. Instead, completely insert the bit, and then back off approximately 2 mm. At least 2/3 's of the router bit shank should be inside the collet.
13 Be sober and not under the influence of medicine that causes a lack of concentration
14 Tidy up your workshop to ensure the ability to move freely with enough room around the router table
| Part No. | Shank dia. | Cutting width | Cutting Height | Radius (r) |
| KPS5901 | 1/2 inch | 7/8 inch | 1 inch | 5/32 inch |
| 12,7 mm | 22,2 mm | 25,4 mm | 4 mm |
Length of Shank: 32 mm
KPS5901Router Bits > Fluting/Beading > Multi-Bead
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy