5" Hex 1WP Ignite Foam Grip Tape - 11"x12" Sheet - 2mm

5" Hex 1WP Ignite Foam Grip Tape - 11"x12" Sheet - 2mmWe have had a ton of people requesting our foam grip tape in sheet form so they could cut out their own custom shapes. Some examples would be if you have a footpad that is not listed on our website. Extra grip and cushion that can be attached to Flight Fins or "Control Freaks". We have even had racers attach it to the bottom of their shoes!! ALL Ignite Grip Tape Foam Grip Tape is PERFORATED to insure an easy install with no bubbles! If you want to add

We have had a ton of people requesting our foam grip tape in sheet form so they could cut out their own custom shapes. Some examples would be if you have a footpad that is not listed on our website. Extra grip and cushion that can be attached to Flight Fins or "Control Freaks". We have even had racers attach it to the bottom of their shoes!!

ALL Ignite Grip Tape/Foam Grip Tape is PERFORATED to insure an easy install with no bubbles!

If you want to add some color to be seen between the hexagons be sure to check out our 1WP Colored Wraps.

INSTRUCTIONS: Please click on the Grip Tape Install video below for complete instructions.

Q&A from Customers:

Q. What causes a board to "Ghost"?(foot pad sensor engages with no rider on the board) A. Several things can cause ghosting. 1st Common problem is from over heating the Foot Pad sensor. This happens when removing the "Stock" grip tape. We recommend using very little heat. Just enough heat to get the surface area of the grip tape to 125F. For any left over adhesive residue we recommend using our "Adhesive Remover". The 2nd Common problem is caused when air is trapped in-between the grip tape and the sensor. This creates an air pocket that puts pressure on the sensor causing it to engaging. ALL Ignite Grip Tape & Foam Grip Tape is PERFORATED to insure no air pockets get trapped in between the sensor and grip tape.

Q. Will the foam tear, where out, or flatten if used by aggressive 200+LBS riders? A. Yes and no... this foam will show some signs of wear but will not tear apart. But it will start to flatten over prolonged use. We recommend our heavier riders to use our 2mm foam for prolonged life.

Q. Will the Images wear off that are printed on the Grip Tape? How do you recommend to clean the grip tape? A. We recommend using a brush. You can add water while brushing to get it looking NEW! When using water we recommend using our Epoxy Foot Pad Sensor Sealant / Plastic & Wood Repair Kit. To insure your FRONT Foot Pad Sensor is properly sealed.

Q. After installing my FRONT foot pad sensor back on my board it will not engage... A. 99 out of 100 times its because you have your tire cable pugged into your foot pad connector and your foot pad cable plugged into your tire cable connector.

Q. Is REMOVAL of the Foam Grip Tape difficult? Do you need a heat gun? A. No, our customized specially formulated 3M adhesive allows for easy removal. You heard that right! We had our 3M double sided adhesive customized so it will stick to wood, plastic, rubber, urethan, & foam. The best part is that all of this was achieved with virtually ZERO residue when removed!

Q. Why is the Foam Grip Tape tearing off in pieces when I am removing it? A. Make sure to pull off our adhesive liner at the same time as the foam. This will insure the foam and grip tape all come off in one piece and not 100's of tiny foam pieces.

Q. Can I install Ignite Grip Tape/Foam Grip Tape on top of my existing grip tape or do I need to remove my old grip tape? A. REMOVE your old grip tape! We NEVER recommend this practice. It is risky and can cause ghosting issues.

After testing multiple designs we have finally cracked the code for no ghosting issues on the new concave front foot pad sensors of the GT! Due to the known ghosting issues of the GT and different riding styles we are recommending the use of Simple Stop. At this moment Future Motion is recommending to all their customers to activate Simple Stop on their mobile app to insure no possibilities of ghosting.  From our testing we have seen where our foam grip tape fixed the issue of ghosting boards. The springiness of our foam helps to pull the sensors apart from each other so they don't accidently detect a rider. I really think we nailed it with this version! However, if Future Motion can’t guarantee their boards not to ghost neither can we. So if you are worried about ghosting turn on your Simple Stop! We will not be liable for any damages caused by a ghosting board.

WARNING: Stock grip tape removal or adding a pad to your front sensor can be potentially hazardous - DO SO AT YOUR OWN RISK.  1Wheel Parts LLC is not responsible for bodily injury or property damages.